How to install 4g vehicle gps tracker and installation precautions

1645509557990429_3728 avatar   
1645509557990429_3728

  Installation Precautions

  1. The external power supply 4g vehicle gps tracker must be connected to the car power supply before it can work 24 hours a day. Because it must be connected to the car power supply, it is different from the general external locator. Therefore, it is not recommended to use an external power supply. 2. Installation location: at the roof light above the front windshield; concealed place in the decorative panel below the front windshield; concealed place around the front instrument panel; in the door partition; under the decorative plate below the rear windshield; (such as The windshield is pasted with a metal heat insulation layer or a heating layer, which will reduce the GPS reception signal and cause the GPS to work abnormally. At this time, pay attention to changing the installation location of the device.) Precautions for use 1. Avoid placing it together with the emission source, such as wireless reversing radar , anti-theft device, and other in-vehicle communication equipment; 2. It can be fixed with a cable tie, or pasted with a wide sponge strong double-sided tape; 3. There are GSM antennas and GPS antennas in the device, and the front side should be ensured during installation ( towards the sky), do not stick to metal objects to block the internal GPS antenna on the sky-facing side to avoid affecting the signal. 4. Avoid low battery of 4g vehicle gps tracker. When installing the 4g vehicle gps tracker, in order to avoid inaccurate positioning, you should also pay attention to the remaining power of the tracker, especially those 4g vehicle gps trackers that do not need to be installed without wiring. If the battery power is too low, it is easy to cause drift, deviation and other results. Therefore, the wireless device should be charged in time to avoid the problem of inaccurate positioning due to insufficient power. Specific installation steps 1. During the installation process, the installation personnel must be civilized and standardized, and must not damage or contaminate the vehicle. 2. Understand the vehicle structure and determine the best installation plan. 3. Confirm the installation position suitable for the vehicle terminal host, GPS antenna, power-off relay, tamper-proof control box, camera, call handle (or scheduling screen or voice announcer). In addition to hanging accessories, the selection principle is concealed installation. The vehicle terminal should be installed in a stable, shock-proof, waterproof, heat-insulating and concealed place. When installing the GPS antenna, ensure that the receiving surface is facing upward, the horizontal inclination should not be greater than 15°, and there should be no metal objects above the antenna or places that are not easily blocked by artificial metal objects. Unless the customer has special requirements, the camera installation position should try to capture the entire interior of the car. The installation position of the call handle and the dispatch screen shall not hinder the normal work of the driver and can facilitate their operation. 4. Find the color and position of the power line (DC 12-24V), ignition switch line (ACC) and other lines closest to the terminal and mark them well. 5. Start wiring after the installation location of each component is selected. The wiring should be neat and consistent with the original wiring of the vehicle as much as possible. The wiring harness must be tightly wrapped with electrical tape to avoid high temperature areas and prevent the wiring harness from being squeezed by some moving parts. The GPS antenna should be installed completely concealed as far as possible, so that it is not easy to be broken or cut off artificially. 6. Line connection. When parallel wiring operation is required, a section of the bare core of about 10-15mm should be pulled from the original wire with a wire stripper, and then the parallel core head should be perforated and then wrapped and tightened; when serial wiring operation is required, Divide the two wire ends to be connected into two strands and twist them with each other, and then join them together to ensure a firm connection. The vehicle terminal is connected with various accessories, the connectors should be aligned and inserted, and the output and input lines should be firmly connected. 7. All newly opened exposed connecting wires are finally wrapped with waterproof electrical tape to prevent the joints from being oxidized and corroded over time. 8. Connect the host, then turn on the backup power supply. If you need to replace the card, follow the steps below: Turn off the backup power supply - unplug the host wiring harness (disconnect the main power supply) - change the card - connect the host wiring harness - turn on the backup power supply. detection. 9. Power-on test to check whether each indicator light is normal: the yellow light (GSM signal) flashes once every three seconds as a SIM card reading, and the green light (GPS signal) flashes once every second as a positioning. 10. The terminals and accessories are bonded with high-strength double-sided tape, and fastened with cable ties. 11. Restore all decorative panels and objects on the car as they are, clean up the debris left by the installation in the car, and clean the car.

  4g vehicle gps tracker https://www.eelinktracker.com/news/the-reason-why-we-need-4g-gps-tracker-not-2g-3g-gps-tracker.html

没有找到评论